£43.65

find out more

£508.47

Crosscut capacity 800 mm (infront of the sawblade)
– Angle fence adjustable from 90° to 45°
– Table size 600 x 650 mm – Fence rail: 1,100 mm for
extension of fence length to 2,000 mm – Guide rail: 1,400 mm

find out more

£656.85

Crosscut capacity 800 mm (infront of the sawblade)
– Angle fence adjustable from 90° to 45°
– Table size 600 x 650 mm – Fence rail: 1,100 mm for
extension of fence length to 2,000 mm – Guide rail: 1,400 mm

find out more

A quick drying sealer which provides an excellent base for all Chestnut Products’ finishes which require the use

of a sealer. This formula does not contain harmful petroleum solvents such as toluene and xylene.

Typical uses - To seal open pores of timber prior to application of lacquers, waxes or polishes. Once dry lightly sand for a smooth surface.

Method of application - Brush, cloth or spray

Drying time - Within five minutes under normal conditions

Coverage - approx. 8-10 m² per litre

Compatibility - Can be used as a basecoat for Melamine Lacquer, Acrylic Gloss Lacquer, Acrylic Lacquer, Ebonising Lacquer, Acrylic Satin Lacquer, WoodWax 22, Woodturner’s Stick Wax, Friction Polish.

Tips - One coat should be sufficient to seal the piece you are working on. Not advisable to apply more than one coat, especially when using a hard topcoat ie lacquers. This product can be tinted using Spirit Stain. Up to 10% of stain can be added to the sealer

Thinners - Cellulose Thinners.

Safety Considerations - Highly Flammable. Our formula does not contain harmful solvents (such as toluene and xylene) but should still be used in a well ventilated place. (see Safety Data Sheet or warnings on can for full details).

Typical uses - To seal open pores of timber prior to application of lacquers, waxes or polishes. Once dry lightly sand for a smooth surface.

Method of application - Brush, cloth or spray

Drying time - Within five minutes under normal conditions

Coverage - approx. 8-10 m² per litre

Compatibility - Can be used as a basecoat for Melamine Lacquer, Acrylic Gloss Lacquer, Acrylic Lacquer, Ebonising Lacquer, Acrylic Satin Lacquer, WoodWax 22, Woodturner’s Stick Wax, Friction Polish.

Tips - One coat should be sufficient to seal the piece you are working on. Not advisable to apply more than one coat, especially when using a hard topcoat ie lacquers. This product can be tinted using Spirit Stain. Up to 10% of stain can be added to the sealer

Thinners - Cellulose Thinners.

Safety Considerations - Highly Flammable. Our formula does not contain harmful solvents (such as toluene and xylene) but should still be used in a well ventilated place. (see Safety Data Sheet or warnings on can for full details).
find out more

£3.95

Beautiful handcast and handpainted 3 dimensional resin pot pourri trinket box lid Approx 85mm diameter.
From left to right, Spring Flower, Poppy and Autumn Berry
find out more

Chestnut Product's Friction Polish produces a high gloss finish ideal for polishing small items. It has a heavy concentration of shellac which gives a very high build; therefore it is not essential to apply a sealer before application, although a coat of Cellulose Sanding Sealer or Acrylic Sanding Sealer may be applied first if you prefer.

Typical uses - High gloss finish usually used on the lathe although it can be applied off the lathe

Method of application - Either by holding a moistened pad against work revolving on the lathe or continued rubbing off the lathe

Drying time - The friction caused by application means that the polish dries immediately

Coverage - Virtually impossible to calculate due to the nature of application

Compatibility - Can be used on bare wood or over any of the Chestnut Products’ Sanding Sealers. The final finish can be treated with Burnishing Cream for an even higher gloss. Waxes can also be applied over Friction Polish.

Tips - Apply a thin coat and keep the cloth moving. For an incredible finish try applying Friction Polish over a burnished coat of Melamine Lacquer then use Burnishing Cream on top.

Thinners - Methylated Spirits (Should not be needed)

Safety Considerations - Highly Flammable. Use Safety Cloth when working on the lathe. (see Safety Data Sheet or warnings on can for full details).

find out more